Saturday, 11 November 2017

A problem with the treadmill, which seems to be due to the motor but turns out to be caused by the belt

A problem with the treadmill, which seems to be due to the motor but turns out to be caused by the belt
Below is a summary of a long email exchange with a customer who had problems that ultimately turned out to be caused by the belt. After testing and changing a lot of components, the customer finally decided to follow the advice ...
J.G. Customer “I have a problem with my TC 470 Domyos treadmill. It happens that after a few minutes of using it at a speed of about 4 km / h the treadmill stops despite the display working. If I come off the belt it starts to turn and if I go back it stops. Until a few days ago it did it once and then worked, but tonight it continues to block. I took off the engine compartment cover and noticed that when it stops is not the belt sliding or anything else but the engine stops. I thought it might be a problem with brushes and then I unplugged the engine from the treadmill but did not open it to avoid further damage. I wanted to know what you could advise me and, if you think it might be the engine, what to do. The engine type is ICON 2.8hp 130VDC / 2089 watts.”
We wrote to the customer: “First, do not use the treadmill in these conditions because of the risk of further damage. The problem depends on the engine, which has probably developed some internal electrical dispersion, this makes it possible to activate the board protection. In turn, damage to the motor can be endemic or depends on the treadmill used or poorly maintained. Could you send me a photo of the engine?”
Customer J.G. “Thanks for the prompt reply, definitely before using it I will have to fix the problem. Anyway I tried to lubricate the belt, but nothing. However, the motor is identical to that of the 2.8 hp 130 vdc Icon that you sell used at 90 euros and you have the photo on your site, or alternatively the new one is compatible with 130 euros. Anyway tonight I'll take a picture and I'll send it to you”.
[We tried to convince the customer to replace the belt, but after some email exchange the customer decided to buy a used engine and not the belt]
 [10 days later ...]
J.G customer: “Hi Luca, unfortunately even with the motor you gave me today, the problem remained, even if it took a minute before it stopped, your motor stops after 15 seconds. With the tester I could not measure the absorption because in my opinion it is only for AC. Anyway the engine for the two times I tried was cool. Now tell me what you can do.”
Our answer: “Do you confirm that it stops after the same time even if there is no one on the treadmill?”
Customer J.G. “Unloaded does not stop but this was also true for the original engine, it's clear I did not go for so much time”
Our reply: “we can send you to test the old engine to see if it can still be used, while for the rest, if the problem emerges always when treadmill is loaded, you need to replace the belt”
Customer J.G. “Why do you say that I probably have to replace the belt? Maybe because it makes too much friction on the board? But it looks new!!! So your suggestion is, I test my motor, I send you back and pay the difference of the new belt, right?
Our answer: “I confirm the offer is that. To control the belt’s quality and friction, you should check how many A absorbs the engine when you are on the treadmill. However, since the components involved are only board, motor, belt, and deck, the probability of the belt is very high, especially if the belt is older than 3 years because it loses its properties.”
[... the client then decides to send his card and his engine for testing]
J.G customer: “Hi Luca, this weekend I did not have to do anything with the treadmill. Anyway I decided to disassemble engine and board and let you have them for testing.”
[after 10 more days we get the results of the lab]
We wrote the customer: “Hi John, I have good news from the lab, which tells me that "new engine, older one and board, all three work fine"
[after a few days the old engine, board and belt are delivered to the customer]
Customer J.G. “Works!!!!! My treadmill started working again, thank you for your help.”
[original text edited and shortened to make it clearer to the reader]

Thursday, 9 November 2017

Replacing the controller for MC 2100

We have MC2100 Icon Controller updated to the latest available technology. The new design of the circuit is improved for greater reliability and uses 1/5 of standby energy compared to older models. The new versions of the MC 2100 series controllers have only 2 AC input terminals. Replacing a previous series controller (MC2000) that has 4 AC input terminals requires a simple wiring change.
1. White AC faston cable Connects to AC NEUT (LG3)
2. Short blue cable goes from AC switch to AC HOT (LG2)
3. Black AC cable connects to the remaining blue wire from the motor. A short extension of the cable must be removed to connect the black to it.
Depending on which controller you are replacing, you may need to change the connector and the supplied connectors. All other connectors (data and sensors) are the same.
Remember: the main reason why the treadmill motor controllers fail is because of lack of maintenance and lubrication of the running deck or because the running belt is too old and generates excessive friction. Protect your investment by checking and lubricating the tape every 40-60 hours of use.
This is the link of the new controller:

Tuesday, 7 November 2017

Modifying shunt resistance- mc2100 board astek treadmill weslo proform nordick track

In this video, we demonstrate how to modify the shunt resistance for calibration on high power motors with the Astek MC2100 controller (10cm diameter engines). It is necessary to use an electrical cable with a section 1-1.5 mm and connect it between the R6 pitch and the shunt resistance. The video shows the situation before the change, where adding a load on the motor causes the card's extra-protection to be activated.

 
The situation after the update is flawless.
 
Buy proform, weslo, nordick track spare parts at http://www.partsfortreadmill.com/
 
Here are the steps of modification:

 
First step: original card, the R6 pitch is free

 
Second Step: We're getting the cable on R6


 
Third Step: The cable is welded on the R6 pitch and is also welded to the shunt resistance.
 
Step 4: Cut off the excess cable

Saturday, 4 November 2017

MC-54 MC-70 MC-2000 MC-2100 Installation and calibration

With the treadmill disconnected from the current, connect all wires to the connectors as indicated. There are a total of 6 (MC54), 7 (MC70), 5 (MC2000), 10 or 12 (MC2100) terminals on the board. Keep all cables away from the white power resistor on the controller (for MC2000 and previous type cards). This resistance becomes very hot during use.
These steps are optional if the board has been repaired / upgraded.
Status 1. Press and hold the speed button + stop at the same time and do not touch any other key while you insert the safety key. This puts the treadmill in setup mode. The speed window will display the maximum speed of the treadmill. Release the buttons. Models manufactured before 1997 have an alternative sequence: press speed - and tilt +.
Status 2. Press the stop button once. The distance window will read % PWM speed signal. The speed window will display the actual speed of the treadmill.
Calibration of the tilt:
While the treadmill is in the state 1 press one of the two tilt buttons. If the gradient is controlled by the console, it will be calibrated automatically. Note: Some models do not have any inclination calibration.
Speed calibration:
WARNING, be on the footpaths of the treadmill or with your feet on the ground. Do not stay on the belt. The treadmill will reach the maximum speed.
Before proceeding, you must locate the speed control trimmer on the controller. It is all white or black with a white center, or blue with a white or yellow center. This is what should be set if speed is incorrect during calibration. The number in the distance window should reach zero.
When the button + speed key is pressed, this number will reach 85 very quickly and the belt will accelerate very quickly. I recommend that you press and release the speed key to increase the number more slowly.
If you reach the maximum speed (as shown in the speed window) before reaching 85, use a screwdriver to lower the speed control trimmer (counterclockwise). When you reach 85, the maximum speed will be displayed in the speed window. Turn the speed controller trimmer up or down to find the maximum speed of your treadmill. It does not have to be exact, but it is better if it is within +/- 3 km / h.
Very important:
When finished, press the speed button - and let the belt stop. Remove the safety key. Reinsert the safety key and try the treadmill. If all is ok, disconnect the current, reassemble the covers and restart.
To keep your board and motor in a working condition as long as possible, follow the directions on our blog. http://www.partsfortreadmill.com/

Thursday, 2 November 2017

Indoor Sports: benefits of treadmill

There are many contrasting opinions if it is best to run at home or outdoors. Outside, you can experience a beautiful panorama, beautiful weather, and the breeze of the wind. Undoubtedly, it is more pleasant to work outdoors, but there are also benefits of training indoors.
1. Race.. weather permitting
"A little rain has never hurt anyone" - but depending on where you live, weather conditions can be a huge problem for daily workouts. Snow or ice can cause accidents during training, and too much heat can lead to dehydration and fatigue. In some circumstances, even air pollution can be dangerous.
2. Security first
No matter the city where you live, going out alone can be dangerous. Most runners tend to get out early in the morning or late at night. And in the winter months, it’s light quite late in the morning and gets dark very early in the afternoon. Why risk the safety factor?
3. Take the necessary amount of water
Dehydration can become a serious problem, especially when doing sports outdoors without having a bit of water with you. Running with a bottle of water is not quite pleasant. Treadmill Benefit: Most standard treadmills come with cup holders.
4. Create your workout
A lot of times, you go out without mapping a path, or your smartphone has a low battery and you cannot use a running app to track progress. The advantage of the treadmill: Many treadmills have programs to help customize and create your own workouts.
5. Easier for joints
Though land can vary from place to place, it is certain: it is unpredictable what can be found outside. From smooth concrete, to sidewalks, to brick, to grass, to dirt. Some of these surfaces can strain your legs, especially the joints. Treadmill Benefit: The tool provides the right texture and cushioning system and helps the muscles and joints.
6. More heart rate control
Setting a target heart rate is the best way to achieve results, whether you want to work on fat burning or whether you want to have a cardiocirculatory training aimed at enhancing the heart-lung system, if you want to follow directions of a physician in rehabilitation. HRC programs on treadmills allow you to set a target frequency and the treadmill will change speed and gradient to keep you as close to the target as possible. The results? An increase of 24% of how many calories you burn in a workout and a strong reduction in the risk of overtaking with heartbeats or vice versa, keeps a rhythm too low and therefore irrelevant.
7. You arrive and leave home
Sometimes it is quite difficult to get out of bed in the morning, change and go out for a workout. Benefit from the treadmill: With a treadmill within arm’s reach, there are no more excuses!

Tuesday, 31 October 2017

How to fix a Treadmill: Practical advice for DIY repairs

Anyone who has a treadmill will have to repair or fix it sooner or later. You may be having trouble with the wear-resistant platform, but it's nothing serious. You can easily learn how to adjust a treadmill by yourself.
Fixing a treadmill, most common things to do:
Check the power supply. Make sure your treadmill is getting proper power supply. Problems with the other home appliances, the sockets, or the use of extension or adapters may diminish the effectiveness of your treadmill, or even damage the electronic control card.
For safety reasons, be sure to turn off power before performing the following steps.
Clean the treadmill. Make sure that there is no dirt or any other accumulation on the treadmill belt, in the motor housing, or the bottom of the rollers. Dirt can cause friction of the belt and will slow down or cause problems during walking and running on the treadmill. When the treadmill is clean, you can turn on the power and check whether the dirt removal has resolved the problem. Do not forget to clean the deck and the belt with alcohol, removing all dirt and lubricant residues and using the new 100% silicone lubricant on the table.
Examine the speed sensor. Check the speed sensor, you can accumulate dust that annoys speed reading, causing various faults during use. Anything that may have accumulated on or around the speed sensor must be removed. A tapering motion or the appearance of an error (E1, E2) a few seconds after the belt is started may be attributed to the sensor covered by dirty, or defective.
Replace the belt. Follow the manufacturer's instructions or those on our blog to remove the motor cover. Loosen the back of the belt with the screwdriver or the keys. Mark the position of the front roller so that the new belt can easily be re-aligned. Pull the belt from the treadmill deck, then put the new belt on the treadmill. Make sure you buy a suitable belt for the treadmill and ensure its good quality. Do not strain too much. Follow the directions of the manufacturer’s booklet or those on our blog.
If you smell burning, clean everything, adjust the belt (reducing the tension as low as possible) and lubricate the deck. If, after doing so, there is still a burning odor, unplug the treadmill and stop using it until the problem is solved. The motor is overheating, causing the burning smell. It may be that the belt is misaligned or replaced or the deck is chipped. Do not continue training with the risk of causing expensive damage to the motor and / or the treadmill control board.
Replace the motor / board. After identifying the failures, this could be the only solution. Follow the step-by-step manual or the directions on our blog. Put all the small parts of your treadmill in a container, so you cannot lose them and you can reassemble all the pieces more easily. This may not be within the reach of everyone. If you are in doubt, contact a qualified technician and never carry out operations without taking appropriate electrical precautions.
After any intervention you should thoroughly test the smooth operation of the treadmill, first without anyone, up to max. speed, then with a test session. During testing, constantly monitor motor and board temperature, if it rises, it may indicate some mounting error or need of further service.
Never use the treadmill with children, people with disabilities or the elderly as long as you are not sure of the perfect working order of the machine. http://www.partsfortreadmill.com/

Sunday, 29 October 2017

How does a DC treadmill motor work? How to avoid treadmill problems?

To avoid problems, it is important to
  • purchase treadmills with motors of high quality and appropriate dimensions,
  • regularly maintain them
  • reduce the coefficient of friction between the belt and deck as much as possible, replacing the belt at regular intervals.
Let's see why these factors are so important
How does the DC treadmill motor work? It is important to have knowledge of the basics so you can understand why it is important to test the treadmill motor properly.
The following applies to most domestic treadmills and some commercial treadmill motors. It does not apply to AC motors, which are mostly used in new commercial treadmills (treadmills for fitness centers and wellness centers).
Permanent magnets (PMDCs) or DC motors are built using fixed magnets mounted around the inside of the chassis. Between the magnets, the center of the engine (inductor) is made by
  • a bearing shaft,
  • a wrap (winding) which consists of wires, insulated from each other by an insulating resin,
  • insulating material and
  • metal blades (battery).
The shaft connects the motor to the running belt of the treadmill via a drive pulley and a transmission belt. The motor provides energy to start the treadmill when you press the start button. But how does the motor convert electrical energy into motion?
Mounted on the shaft inside the engine there is a core of iron (rotor) and around it there is a wrap of copper wires known as windings or coil. An electric current is passed through the windings of the motor.
The current comes from a motor control board that is connected to the motor via two brushes. The engine controller's job is to change the AC (alternating, usually 220/240) voltage into the DC and adjust the voltage.
The motor would not work (indeed it would be damaged) if it was directly connected to the wall outlet. The motor control card also allows you to change the motor speed by adjusting the voltage to the motor according to the speed set on the treadmill console.
When the electric current passes through the windings inside the magnetic field (created by permanent magnets), the shaft rotates to bring the magnetic balance back to the engine rotation. The rotational power of the motor depends on the force of the magnetic field created by the permanent magnets and the amount of current which travels through the copper windings. Therefore, the bigger the diameter of the motor is the better it is. Because the magnetic field of the permanent magnets is greater and the power at the same current is greater.
In the motor, it is important to couple the concept as it is necessary to make sure that you have a sufficient torque so that the treadmill moves smoothly when you are on it. The motor torque is normally indicated in Watt or Horse Power (HP).
You can increase the torque by increasing the magnetic field of permanent magnets (i.e. using a larger motor) or by increasing the current flowing through the windings. In practice, it is not possible to increase the magnetism of permanent magnets (they are permanent and cannot be changed). So you need to increase the current through windings to get more torque.
The amount of current that can pass through copper wires is limited by the size of the wires and the capacity of the motor control board (MCB) that provides electrical current. If you try to pass too much current you can burn copper windings, which will cause them to blend, or overburden, destroying them.
Small electric dissipation can go unnoticed in a bench test or running the motor with a car battery, but this can cause problems when the engine is connected to the control board and subject to high voltage. http://www.partsfortreadmill.com/