Saturday, 15 February 2014

Treadmill Test Mode (Endex Controllers)

Procedure:
i.     When the console is at standby status, press “ENTER” and “INCLINE  ︿” (or hold “SPEED  ︿” and turn on the machine)  to enter the Engineering
Mode.
ii.    Console scan mode goes on(all digits go flashing and off  ).
iii.   Press “ENTER” to switch the scan mode(Data Line).
iv.   Press “ENTER” to switch the scan mode(Scan Line).
v.    Press “ENTER” to switch the scanning of a single LED.
vi.   Press “ENTER” to switch the scanning of the decimal point.
vii.  Press “ENTER” and the Dot Matrix Window shows “KEY”, the Alpha Numeric Window shows “KEY VALUE=” and then it enters keyboard test mode.
viii.  Press “ENTER”, the Alpha Numeric Window shows “ATUO TUNING” and then it enters automatic tuning function.((((Only for AC motor))))
ix.   Press “START” and “SPEED  ︿” to start, the Alpha Numeric Window shows “PLEASE WAIT”. Time starts to count and it stops after a 25-second counting, then the window shows “TUNING OK”  (Note: Do not step on the running belt when the Automatic Tuning is on).
x.    Press “ENTER” , the Dot Matrix Window shows “IO” and it enters IO test mode.
xi.   Press “ENTER” to control the relay switch; press “INCLINE  ︿” to incline up; press “INCLINE  ﹀” to incline down; press “SPEED  ︿” to speed up; press “SPEED  ﹀” to speed down; the Heart Rate Window shows heart rate; the Incline Window shows ADC value and the SPEED Window shows
feedback of speed.
xii.  Press “ENTER” to test again or press “ENTER” and “INCLINE  ︿” to return to the standby status.

Buy Endex controllers on our eshop

Treadmill Engineering mode (Endex Controllers)

1. Engineering Mode Procedure:
i.     When the console is at standby status, press “ENTER” and “SPEED  ︿”  to enter the Engineering Mode.
ii.    The Dot Matrix Window shows VER; the Alpha Numeric Window shows model and version; the Incline Window shows year; the Time Window shows date and the Speed Window shows wheel(roller)  size.
iii.   Press “ENTER” button to show version of motor “LD” or “ISP”.
iv.   Press “ENTER” button to enter the Metric/English system setting.(see the instruction in Clause 2)
v.    Press “ENTER” button and the Dot Matrix Window shows “INPUT WHEEL SIZE”, enter the wheel size setting(Metric system: 400~900,±1, Default: 635; English system:1.60~3.50, ±0.01, Default: 2.50)
vi.   Press “ENTER” and the Dot Matrix Window shows “INPUT MIN SPEED”, enter the min. speed setting(Metric system: 0.8~1.5, ±1, Default 0.8; English system: 0.5~1.2, ±0.1, Default 0.5)
vii.  Press “ENTER” and the Dot Matrix Window shows “INPUT MAX SPEED”, enter the max. speed setting(Metric system: 10.0~20.0, ±0.1, Default: 10; English system: 6.0~12.4, ±0.1, Default: 6.0)
viii.  Press “ENTER” button to show the total distance of storage currently.
ix.   Press “ENTER” button to show the total time of storage currently(Hours).
x.    Press “ENTER” button to return to the standby status.
Note: Press “ENTER” and “INCLINE  ﹀” to initiate the system.

2. Metric/English Setting Procedure
i.     When the console is at standby status, press “ENTER” and “SPEED  ﹀”  to enter the Metric/English system setting.
ii.    The console shows “KMTYPE = KM”. Press “︿” or “﹀” buttons to select Metric/English system(KM stands for Metric system ; ML stands for English system)

Buy Endex treadmills controllers on our eshop.

Treadmill Engineering Mode & Test Mode

Following information is valid for most of treadmills equipped with Endex Controllers

There are two different modes of operations built into the console which are useful for getting information and testing certain functions of the treadmill.

The different modes are:
1.    Engineering Mode:
This mode goes through what software version is being used on the treadmill, the software parameters, the ability to change between Metric and English units, the total mileage on the treadmill and the total number of hours the treadmill has been used.

2.    Test Mode:
This mode takes you through several different functionality checks for the console and a quick check on the MCB Start Relay Switch. This allows you to see all the readouts on the console, checks all the buttons functionality, checks for incline functionality and Test/Calibration and checks to make sure the MCB is capable of driving the running belt.


Treadmill E6-E7 error flowchart


Treadmill E1 error flowchart

Buy speed sensors on our eshop

Compact Treadmill Main Parts Replacement

 treadmill replacement parts
Motor Hood removal and replacement
Tool: Allen wrench & Phillips screwdriver

Removal steps

Rear End Cap and Carrying Bar removal and replacement
Tool: Phillips screwdriver & Allen wrench.

Rear Roller removal and replacement
Tool: Allen wrench.

Buy treadmill parts online www.partsfortreadmill.com