Saturday, 25 November 2017

Problem: Nordick Track treadmill jumps out, solved with 110V motor replacement with 180V motor

Let's summarize the experience of this customer
The customer sent us as his board and engine to be tested at the laboratory. The lab found a defect, which was leap current
Lab finds KO motor short, controller to be repaired.
After some time, the customer receives the card and the original engine (new) Nordick Track.
After some time, the customer contacts us again saying that he has another problem, this is his description of the problem: «I tried it for 25 minutes after which I turned off everything, I checked the fuse that was close to the plug and it was blown, I reactivated it but as soon as I start the treadmill, the engine starts to turn “jumpy”, I also tried without the engine connected. Your technician told me that even without the engine the light should blink but instead it remains off”
After a few days the controller came back to the lab, and we find out that the board is damaged again on the power output part, probably due to incorrect maintenance or "load" side issues. The controller is still repaired and the customer is required to pay a very reduced fee for the repair.
The lab confirmed that they replaced the power part of the card. It is the part which gets damaged in case of "load" problems, such as wrong maintenance, old tape (too much friction), etc.
Even after this the customer still complains about the treadmill malfunction. It starts, you can walk on it for 5 seconds and then it stops again. Without anyone (unloaded) works fined, but with a person of about 60/70 Kg stops
A replacement board is then sent to the customer, which accepts both 180v motors and 110V motors. The treadmill works fine a few weeks, after that it still notices problems with the card.
The new board (with original engine) causes the same problem. The customer agrees to try the replacement engine 180V.
After that we received the new message from the customer: “Good morning Luca, I tried with the engine that you sent me. It looks like it's okay now. I used it for about 40 minutes and it did not stop. I wanted to ask you if it is normal that after the 40 mins training the engine gets quite hot. Thank you.”
Afterwards we sent the customer instruction on how to adjust the main running belt and the drive belt.
He wrote us back: “Sorry for the delay, now it looks like it's okay” www.partsfortreadmill.com

Thursday, 23 November 2017

Problem after replacing the treadmill motor

Question
I replaced the treadmill motor with a new one, and connected it. Now I have a problem, the treadmill without any command starts at maximum speed. Faston connectors are properly connected (red + black –) if I put them opposite, treadmill reverses direction and stops immediately after that. Please help.
Answer
To reverse the direction of the treadmill, it is enough to reverse the red and black cables, unfortunately the fact that it starts immediately at maximum speed means the control board is short-circuiting.
So, you may want to check if it can be repaired or not.

Tuesday, 21 November 2017

Modify icon brand treadmill (Nordick Track, Proform, Weslo), with larger engine (180V)

Example treadmill modification using a “3 HP Mega Motor” motor type and an Eway compatible controller www.partsfortreadmill.com
Here are some advantages:
- the use of a bigger engine (10 cm in diameter compared to 8 of the original engine), allows better heat dissipation and reduces engine overheating even under harsh conditions
- The use of 180V motor technology allows a reduction in the current (A) resulting in further reduction of the risk of overheating and consumption. It is also more suitable for use in Europe (where the mains current has a voltage of 220 ~ 240VAC)
- The most powerful engine is suitable for longer use
A similar result can be obtained by applying a change to the original Icon Controller board, as follows

Sunday, 19 November 2017

I cannot measure the belt of the treadmill

Question
I guess I cannot measure the belt because it's sliced so I can do it??
Answer
If it is broken, cut it with a cutter, pull it out and then measure it. If you do not succeed, you have to pass a string along the entire length of the path the belt should have, from there you can find the length. You should also check (by removing the lateral end caps) the position of the adjustment nuts, to understand if it is better to replace with a little longer or a little shorter belt than the original.
The list of belts we have available is on the internet and you can find it at the following link. They cover almost all makers and models of treadmills, tailor made belts for special models are also available.

Friday, 17 November 2017

How to Repair Bike Computers

You can do the adaptation by splicing the cables and connecting them directly if the contacts do not exactly match those of the original computer.
Speed sensor (Sensore n. giri in the pic) is always a single-pin 2-pin cable that differs from the others. Two pins are almost always enough for the bike speed sensors.
The double connectors (sensori cavi pulsazioni) are 2 cables, usually one of the two is white, they are handpulse sensors. They might be 3 or 4 wires. Each pulse need at least one cable + one which may be in common.
Note that if the bike has jack type connectors (headphones), these are interchangeable with those of the example computer above, but if you see a connector made up of a single long cable strip, this is not compatible and you need a different computer (bike “ergometer” computer with automatic tension adjustment).

Wednesday, 15 November 2017

Error E1, E2, E3, L5 and LS on treadmill

Question
My Prorun K30 treadmill has problems with the motor, it starts but stops shortly after, and L5 error appears on display. I would need technical assistance or any information about any check I can do to understand what’s the problem.
Answer
Error L5 is like error E1. It would better read as LS (low speed). Usually you can fix it by replacing the speed sensor or the motor controller.
In fact, for the E1 and the similar errors (some models call it E2, E3 (rare), low speed, or LS) you have to distinguish
- If the treadmill runs for a few seconds and then stops showing E1, low speed or similar -> 99% is the sensor that does not work anymore. BUY SPEED SENSOR (you can find them on www.partsfortreadmill.com)
- If it works for some time (minutes) and then stops showing E1, it is often the controller that goes into protection (may be worth checking the running belt if old or not lubricated, and also check problems with the motor such as electric leaks.) Buy motor, belt or test your engine. (see www.partsfortreadmill.com)
- if it clicks and then stops, the controller is short or the motor is short. Test them. (see www.partsfortreadmill.com)
- if it does not move at all, 99% the controller is faulty. Replace the controller. (see www.partsfortreadmill.com)

Monday, 13 November 2017

Adjusting the treadmill belt if it does not keep the position

Question
 I ask you kindly to explain what should I do on the treadmill that presents this little problem:
- the belt slowly moved all in the left part (seen from above) and is therefore no longer "centered"; what adjustments should I take, should I adjust on the front or on the rear roller?
Answer
The front roller must be perfectly aligned and should never be touched for adjustments.
To adjust the belt, you can use only one of the nuts on the rear roller, turning it clockwise or counterclockwise depending on the effect it seeks (if you remove the two endcaps, it will be easier for you to see what happens).
When adjusting the treadmill should be going at around 2/3 km / h unloaded (nobody on the belt) and you can start by turning the nut (1 full turn / if no effect repeat with max another turn), so that the belt returns in the central direction. Once the center is reached, the belt will tend to "go to the other side", so you should turn maybe 1/4 or 1/2 turn in the opposite direction to the initial adjustment to settle.
If it seems good now, you can gradually increase the speed, checking that at higher speeds your belt do not tend to move (in which case you repeat the operation again, with ever smaller and more accurate adjustments) until you reach the max speed.
Notes
1) If at first it is very "off-centered" you can initially push it manually (pointing your feet when the belt is turning at low speed) to make it go a bit in the middle. This is to prevent the belt from ending up on the rim of the footrest and ruining, crawling on.
2) If you need to adjust very frequently, check the leveling of the feet and the floor itself. Also check if the running belt is not under-tightened (avoiding, however, to over-tighten). If even tapered and well tensioned, the belt tends to move around, check your own way of walking / running because probably you don’t run in the middle, or you push with one foot more than the other and this can be a good opportunity to fix a little for a better training.
---------- Running belt tension instructions (if necessary) -------------


You can self-test and adjust the correct belt tension. Turn both adjustment knob to release tension from the running belt until it slips on the roller when loaded. Then tighten it slowly up to the best coupling. Be careful that if the running belt is old (> 4 years old) and very tighten, it is better to replace it with a new low friction belt.
To set the correct tension of the belt, remove the motor cover, start the treadmill (should rotate at low speed), climb onto the belt, hold the handrails and try to lock the belt.
Check whether the engine continues to rotate but the belt stays it means something is slipping (the belt, the drive belt or the pulley).
Tighten the belt and until the belt - roller – drive belt - motor coupling is perfect, do not over tension, because it only adds load to the treadmill, resulting in early wear on the transmission system and board / engine parts. http://www.partsfortreadmill.com/