Treadmill Elevation Motor removal and replacement

Incline motor removal in a treadmill

Adjust treadmill motor controller board after motor change | Astek treadmill boards

1. Please adjust the IR, LIMIT and SPEED value on the MCB.

2. For Turdan Motors, adjust the IR value to 11 and LIMIT value to 5.5

3. For Turdan Motors, adjust the SPEED value to 8.5

Treadmill E1 error | change the optical speed sensor to a magnetic speed sensor without replacing the original power board

In case you need to change the optical speed sensor to a  magnetic speed sensor without
replacing the original power board please do the following:

1) Fix the magnetic speed sensor to the correct place pointing towards the magnet
in the front roller. Leave the distance between sensor and magnet 2 - 3 mm

2) a. Connect the speed sensor to the power board by using the 2 pin cable: 

    b. or cut original wires, and connect wires directly. Red is not connected. (close up open 
        wires with shrink-hose)
    c. or connect the 2 pin plug directly on the 3 pin socket on PCB. Right 2 pins are used. Left      
        one is not connected. Pls make sure connector is fixed properly to the socket (glue).

Please connect the power and manually rotate the front roller to see if the speed signal appears
on the power board on LED in position D30

Repair StrengthMaster Treadmill AC motor autotuning

1) Press enter + speed up + incline up 

2) Keep pressing “Enter” till the main window shows up “AUTO TUNING”

3) When LED below show “AUTO”, Press “Start” and speed “up” buttons to proceed auto tunning.
Warning: Do not stand on running belt when proceeding auto tunning.         

4) Abour 25 seconds later, the main window will stop without any numbers.

5) Press ENTER and incline “up” back to stand by mode as below.

Broken controller? Buy the replacement here:

Treadmill Inverter for professional equipment Endex Jim224

Treadmill Inverter compatible with Technogym Spazio Forma models

Treadmill Inverter compatible with Technogym Run Race models

Treadmill Inverter compatible with Technogym XT / XT PRO models

Treadmill AC Retrofit KIT: Inverter + cabling + potentiometer + alternating current (AC) motor

Other parts

 

 

 

 

Treadmill error codes MCB ALT 6090

8.1『E01』：SPEED SINGAL IS MISSING

8.2『E02』：OVER VOLTAGE PROTECTION

8.3『E03』：OVER CURRENT IS MUCH MORE 5 SECONDS

8.4『E04』：MOTOR PROBLEMS

8.5『E06』：COMMUCIATION FAILURE

8.6『E09』：INCLINE CHECKING PROBLEMS

8.6『E0P』：SPEED CHECKING PROBLEMS

8.7『E0C』：SHORT-CIRCUIT PROTECTION

8.8『E0E』： EEPROM  IS DAMAGED 

Treadmill troubleshooting: No display on meter

No display on meter
 
Be sure the power is right.
If new treadmill, be sure the connect cable pins are OK
If used treadmill, it maybe some PCB components broken or transformer broken. Let the engineer check using multimeter.

Buy a replacement parts here: treadmill controller; transformer and cables; treadmill repair

Treadmill errors e0 e1 e3

Buy treadmill controller and treadmill speed sensor on our eshop.

PCB ERROR CODE AND SOLUTION
ERROR CODE	PROBLEM	SOLUTION
E0	1. no safety key	1. connect safety key
	2. safety key sensor broken	2. open the console case, replace the sensor under the safety key (use one of these sensors).
	3. safety key does not work.	3. replace the key.
E1	1. motor does not work	1.change or rework the treadmill motor
	2. speed sensor does not work	2. change or rework the speed sensor
	3. roller magnetic not work	3. change or rework the roller
	4. connect wire not work	4. change or rework the wire
E3:Only caused when use 'MODE' key	1. motor speed can not be control	1. change motor
	2. motor not work	2. change motor
	3. speed sensor not work well, no signal.	3. change speed sensor